MINI IR HIGH SPEE DOME CAMERA

MINI IR HIGH SPEE DOME CAMERA

 

 

User Manual

 

 

 

Power Supply DC 12V

Factory Configuration: PELCO-D protocol,Baud rate 2400, address code 1

 

Safety Precautions

 

 

  1. Careful Transport
    Transport, storage and installation process, we need to prevent stress, severe vibration and damage to the product immersion.
  2. Careful installation of movement
    To be especially careful, light-light, do not force squeezing movement and the structural components, so as to avoid the ball machine trouble. For security reasons, do not cover the ball is not installed electricity.
  3. The power, video lines and control lines
    Power lines, video lines and control lines preferable to use shielded cable and is independent of routing, can not blend together with other lines.
  4. Electrical Safety
    In use must comply with all electrical safety standards, the ball machine or signal transmission line should work with high-voltage equipment or cables to maintain a sufficient distance (at least 50 meters), if necessary, do a good job against lightning, surge and other protective measures.
  5. Cleaning
    Cleaning the camera housings, please use the dry soft cloth, such as severe dirt, use neutral cleaning agent gently wipe. Do not use strong or with abrasive cleaning agents, so as not to scratch jacket, affecting image quality.
  6. Note that strictly sealed to prevent liquid splashing into or foreign bodies falling into the ball machine, otherwise it will result in permanent damage to the device.
  7. Do not exceed the limits of temperature, humidity, the use of state of the camera. Camera use temperature of -25 to 50 , humidity of less than 90%.
  8. Do not install the camera near the air conditioner outlet.
    In the following cases, the lens because of water vapor condensation born fog.
    From the air conditioner off when you open when the high and low temperatures caused by the rapid change.
    Caused by the door when the switch level of the rapid temperature changes.
    Glasses fogging in the environment can be
    l used.
    In a room filled with smoke or dust used.
  9. Do not be a long time the camera toward a strong light source, such as the sun.
    Spotlight and other light sources will cause screen aging. A long time the camera toward a strong light source may be due to the color filters on CCD damage caused by loss of color images.

Catalogue

catalogue    3

Chapter 1 Product summarize    4

1.1 product synopsis    4

1.2 technical parameters    4

1.3 function explain    5

Chapter 2 equipments’ installation    8

2.1 camera’s dial-up and switch setting    8

2.2 Camera’s structure and size    10

2.3 High speed dome installation    11

Chapter 3 Menu setting and operate    13

3.1 Basic operation    13

3.2 System OSD menu operate    14

3.2.1 main menu    14

3.2.2 menu’s operation    15

3.2.3 <SYSTEM INFORMATION>    15

3.2.4 <ADDR SETTING>    16

3.2.5    <MOTION>    16

3.2.6 <SET FRAME SCAN>    17

3.2.7 CLEAR FRAME SCAN    18

Chapter 4 simple error and maintain    21

4.1 simple error exclude form    21

4.2 After Service    22

 

Chapter One Product Summarize

1.1 product synopsis

Security and fire monitoring system, as the latest video surveillance equipment. Ultra-small 4-inch integrated intelligent high speed dome camera is used the latest scientific and technological achievements of today’s most precise angle of the manufacturing process; integrated years of experience successfully developed, equipped with 10-fold MINI automatic zoom lens, high-performance digital signal processing ( DSP) camera; set of built-in PTZ and digital decoders in one, representing a new generation of high-tech surveillance product development trend. It uses all-digital control, mechanical design ingenious simple, quick positioning and continuous tracking of arbitrary scanning a real sense of all-round, non-blind intelligent surveillance; can automatically adapt to environmental changes in light and shade and target distance; the level of 360 ° rotation, precision stepper motor drive, run a smooth and precise positioning; built-in full-screen OSD screen menu is compatible with a variety of control protocols, baud rate adjustable; high reliability, no maintenance.

Ultra-small 4-inch integrated intelligent speed dome camera is the latest technological developments in the field of security to solve the indoor monitoring the outcome of the whole point of view, no blind spots, beautiful appearance, easy to install wiring, and so a number of advantages. These features make it applicable to all walks of life indoor large area, moving target surveillance. Such as indoor public system, subway, the telecommunications sector, banking security, office buildings, intelligent buildings, intelligent plot, airports, railway stations and other monitoring.

1.2 Technical Parameters

 

Model Number

SD-HZ39-10

SD-HZ49-10with IR-CUT

SD-HZ29-10N

SD-HZ49-10Nwith IR-CUT

Image sensor

1/4CCD

Signal mode

PAL/NTSC

Horizontal resolution

Color 480TVLB/W600TVL

Effective pixel

752horizontal×582Vertical

Minimum illumination

Color to B/WIR SENSOR Color 0.05LUX,B/W 0.001LUX

S/N ratio

≥60dB

Backligh compensation

ON/OFF

White balance

Auto

Electronic shutter

1/501/12000s

Focus length

3838mm

Optical focus

10x

focus

manual/Autotake high-performance DSP to realize complete digital and ulta-high speed focus function

Presets

256

Patrol Track

4groups,each can record 100 actions

Cruise track

30 presets can join cruise, can setting the presets’ residence time.

Other scan

Support Horizontal scan, deuce area scan, scan random

Rotation Range

Horizontal 360°unlimted rotationVertical 180°auto reversal

Rotation speed

Horizontal&Vertical Min 0.01° Max 300°/s.

Communications

PELCO-D and PELCO-P

OSD

Full screen menu

Temperature Control

Optional

Power supply

DC12

Dimension

4 inch

Material

Aluminum shell, waterproof IP66

Wrok Environment

-20+50select temperature control accessories),﹤95%RH

1.3 Function Description

Ultra-small 4-inch brief intelligent high speed dome camera integration, the main function of
1. Set address coding, baud rate, control protocol
Any operation commands the camera has its own objectives address coding, baud rate, control protocol, a single camera only to respond with its own address coding, baud rate, control agreement under the operation of the command. Camera address coding, baud rate, control protocol specific settings please refer to the dial-setting methods.

2. Tracking
Users can use the controls on the keyboard joystick control of the upper and lower turning left and right cameras can be used to track moving targets or moving horizon, while the focal length can be adjusted to change the perspective of the size or the target image size. In the auto-focus of the state, with the lens rotation, the camera will automatically adjust according to a rapid scene changes, instantly get a clear picture.

3. Focal length / speed automatic matching technique
    Manual adjustment, the longer the focal length of the case, a reflection of high-speed ball machine makes a slight touch screen joystick may move back, resulting in data loss.
Based on user-friendly design, intelligent ball according to the proximity of the focal length of the camera automatically adjusts the horizontal and vertical speed, so that manual operation is more simple and easy to track targets.


4. Auto MDIX
The operator will pull the bottom of the lens (vertical) after it is still holding down the joystick, this time the level of the lens auto-rotated 180 ° turning up immediately after the 90 °, can directly watch the back of the scene in order to achieve the full 180 ° continuous vertical surveillance.

5. Settings and call preset position
Preset function is the current state of the ball under the PTZ function of the horizontal angle, tilt angle and camera lens focal length, etc. position parameters stored in memory, you need to call these parameters can be quickly and PTZ cameras will be adjusted to that location. The operator can quickly and easily by controlling the keyboard, infrared controller, control equipment such as storage and call the preset point, the ball machine to support 256 preset points.


6. Lens Control
    (1) Zoom control
    
Users can control the keyboard or through the ball machine to adjust the focus of the distance matrix of the host, receive the necessary panoramic images, or is a fine view.


(2) Focus Control
    System default auto-focus, zoom, the camera lens will be the center of the screen features auto-focus, to maintain a clear picture; in exceptional circumstances, the user can manually focus, achieve the desired image effect.
    When in manual focus state, to restore the auto-focus, as long as the sway bar can be restored remotely auto-focus. There is also a dedicated control commands can be issued or to call an arbitrary way of restoring a preset bit auto-focus.
    The camera lens in the following situations will not autofocus on the camera objectives:
    
a. Target is not to screen center;
    
b. Targets the same time in the far and near the place;
    
c. Target light objects, such as neon lighting, spotlights and other luminous objects;
    
d. Target with droplets or dust behind the glass;
    
e. Targets moving too fast;
    
f. Large area targets, such as walls;
g. Objectives are too dark or inherently ambiguous.


7. Aperture Control
Users can control the keyboard, manually adjust the aperture size, to obtain the required picture brightness.
  
8. Auto Backlight Compensation

When the backlight compensation function is open, the camera lens in the light background can be automatically targets the more the dark luminance compensation. On the bright background light adjustment, to avoid the background brightness caused by a mass of light throughout the picture, goals and not identifiable because of the darkness to gain a clear image.
 
9. Auto White Balance
According to the changes in ambient light, automatic adjustment, the true color reproduction.

10. Night vision function (color / monochrome conversion)
Cameras with night vision function, automatic color / monochrome conversion mode, in accordance with changes in ambient light automatic conversion CCD illumination. Such as: adequate lighting during the day due to the use of general illumination to ensure colorful images. In the night illumination can be automatically changed to black and white images show a clear interest.
11. Cruise
Can be pre-set cruise preset point, certain preset points, organized in the order required to auto-cruise in the queue, only an external command can be in an indoor speed ball set automatically according to preset points in order to provide the time interval constant movement back and forth.
12. Pattern scanning
  Pattern scanning machines to run the ball through the menu, the trajectory is stored down by power-on action, free movement, alarm linkage, etc. to call the stored scan line.

13. Continuous scan
Just an external command or through a power-on action, free movement, alarm linkage, etc. to call, can make the ball machine horizontal direction to a certain speed the cycle of continuous scanning.
14. Batch Scanning
Just an external command or through a power-on action, free movement, alarm linkage, etc. to call, can make the horizontal direction the ball machine cycle of a certain speed intermittent scan.
15. Area scan
Just an external command or through a power-on action, free movement, alarm linkage, etc. to call, can make the ball machine horizontal direction to a certain speed, within the limits set by the community and from scanning.

Chapter 2 Equipment installation

2.1 Camera’s dial-up and Switch setting


Ultra-small 4-inch integrated intelligent speed dome camera is compatible with a variety of control protocols, baud rate can be adjusted to make it compatible with more of the monitoring system. In the fixed installation of ball machine before, according to the need to adjust the DIP switches to the appropriate coding, to change the baud rate of the ball machine, control protocol, address coding. If there are no special requirements, the ball machine factory default value for the address coding “1”, the baud rate is set to “2400BPS”, Control Protocol is set to “PELCO-D”.

Ultra-small 4-inch integrated intelligent speed dome camera can be DIP switch to change the ball machine, “Baud Rate (BAUD-RATE)”, “Control Protocol (PROTOCOL)” and “address coding (ADDRESS)”. Ball machine movement DIP switch plans, such as:

as

Note: 4 DIP switches as follows: baud rate and control protocol switch
      8 DIP switches as follows: Address DIP Switch

 

DIP switch appropriated for “ON” means “1”, DIP switch appropriated for “OFF” means “0”, DIP switch on the left for the low, right is high

Baud rate and control protocol setting form:

No.

1 

2 

3 

4 

 

Buad rate

BPS

   

ON

OFF

2400

   

OFF

ON

4800

   

ON

ON

9600

Control protocol

ON

OFF

   

PELCO-D

OFF

ON

   

PELCO-P

 

8-bit DIP switch is used to set the ball machine address coding.
Address set binary mode can be set to a total of 256 different ball machine address coding, see coding table address.

 

Camera address

Coding form

1 

2 

3 

4

5 

6 

7 

8 

0 

OFF 

OFF 

OFF 

OFF 

OFF 

OFF 

OFF 

OFF 

1 

ON 

OFF 

OFF 

OFF 

OFF 

OFF 

OFF 

OFF 

2 

OFF 

ON 

OFF 

OFF 

OFF 

OFF 

OFF 

OFF 

3 

ON 

ON 

OFF 

OFF 

OFF 

OFF 

OFF 

OFF 

4 

OFF 

OFF 

ON 

OFF 

OFF 

OFF 

OFF 

OFF 

5 

ON 

OFF 

ON 

OFF 

OFF 

OFF 

OFF 

OFF 

6 

OFF 

ON 

ON 

OFF 

OFF 

OFF 

OFF 

OFF 

7 

ON 

ON 

ON

OFF 

OFF 

OFF 

OFF 

OFF 

8 

OFF 

OFF 

OFF 

ON 

OFF 

OFF 

OFF 

OFF 

9 

ON 

OFF 

OFF 

ON 

OFF 

OFF 

OFF 

OFF 

10 

OFF 

ON 

OFF 

ON 

OFF 

OFF 

OFF 

OFF 

11 

ON 

ON 

OFF 

ON 

OFF 

OFF 

OFF 

OFF 

12 

OFF 

OFF 

ON 

ON 

OFF 

OFF 

OFF 

OFF 

                 

246 

OFF 

ON 

ON 

OFF 

ON 

ON 

ON 

ON 

247 

ON 

ON 

ON 

OFF 

ON 

ON 

ON

ON 

248 

OFF 

OFF 

OFF 

ON 

ON 

ON 

ON 

ON 

249 

ON 

OFF 

OFF 

ON 

ON 

ON 

ON 

ON 

250 

OFF 

ON 

OFF 

ON 

ON 

ON 

ON 

ON 

251 

ON 

ON 

OFF 

ON 

ON 

ON 

ON 

ON 

252 

OFF 

OFF 

ON 

ON 

ON 

ON 

ON 

ON 

253 

ON 

OFF 

ON 

ON 

ON 

ON 

ON 

ON 

254 

OFF 

ON 

ON 

ON 

ON 

ON 

ON 

ON 

255 

ON 

ON 

ON 

ON 

ON 

ON 

ON 

ON 

2.2 Camera’s Structure and Size


 



  1. High speed dome camera installations

The ball machine installation process such as: remove the transparent cover, fitted with ball machine pinch, pinch bracket mounted on the wall, in the ball machine to be installed on the wall to determine the installation location, according to bracket screw hole location on the wall with the signal pen draw holes in the walls of the expansion of drilling screws into the hole; the cables through the bracket, and then screw on the bracket alignment screw will tighten the nut,
The ball machine head alignment bracket air into the hood, tighten the bracket screws on the three to prevent the ball machine off.

Specific installation diagram is as follows:

The first step: remove the ball machine and transparent cover, the ball machine to adjust system settings



The Second Step: fitted with ball machine pinch




 

The third step: in the installation of wall to determine location of mounting screws holes


The fourth step: in the installation location of drilling, expansion screws into the hole



The Fifth Step: cables through the bracket, fixed bracket


The Seventh Step: fitted with ball machine


Chapter 3 Menu setting and Operate

3.1 Basic Operation

3.1.1 Power-On Self-Test
      
The ball machine power, the camera horizontal and vertical movement, the screen will appear system-related information, such as dome-associated system message disappears, the dome camera self-test to complete the following diagram

 

 

PTOL PELCO-P

COMM 2400N81

ADDR 1

DisplayPELCO-P protocolBuad Rate 2400Address code 1

3.1.2 control the camera rotating around the upper and lower
   After selecting a camera, you can manually control the keyboard on the joystick up and down around the dome camera movement. The shake control joystick moves the camera, when the joystick to the right shake, the camera is also to right. Similarly, when the joystick to the left when the camera shake movement is also to the left. Rocker vertical shake when the camera also follows the appropriate action to do the vertical direction.
Shake the joystick according to the diagonal direction, it can allow the camera to do the same time, horizontal and vertical movement, and direction of motion consistent with the joystick.

3.1.3 Lens Focus Control
Note: Different manufacturers keyboard preset keys are different, the keyboard manufacturer.
By controlling the keyboard on the “ZOOM-” and “ZOOM+” button to control the variable lens multiples (ie, closer, pulling away).
By controlling the keyboard on “FOCUS-” and “FOCUS+” button to control the focusing lens (camera must be set to “manual” focus or the “Auto / Manual” focus to be effective).
Note: The following situation may occur can not focus on the case
 a: are looking at target is not to screen center.
b: At the same time observe the distant and near targets, not at the same time ensure that front and rear are clear.
C: target for the light body, such as spotlights, car headlights and so on.
d: target is moving too quickly or the environment too dark.
Iris control of most of the camera for automatic Iris control, and if manual control over Iris, through the keyboard on the “IRIS+” and “IRIS-” button to complete the Iris open and closed
3.1.4 presets setting

Setting Presets:
   (1) selected camera (see manual control of the keyboard);
   (2) operation Rocker, zoom button, focus button, buttons adjust the camera aperture screen;
   (3) Press the number keys + PRESET (input designated preset) to preserve the scene preset parameters.
Call preset points:
   (1) Selected camera;
   (2) Press the number keys (inputs the designated preset) + PREVIEW button, the camera immediately move to the preset position, the lens zoom, focus and Iris is also automatically change to the preset parameters; if the input is a special function preset point (see “Preset Point menu”), the dome camera will perform with special features preset point of the corresponding functions (such as: Enter the 80th presets, the camera will perform auto-tracking feature).

Presets Function form

Dial the 95th Presets

Enter Main menu

Dial the 82nd Presets

Auto Cruise

Dial the 83th Presets

clear all presets

Dial the 84th Presets

use Patrol scan 1

Dial the 85th Presets

use Patrol scan 2

Dial the 86thPresets

use Patrol scan 3

Dial the 87th Presets

use Patrol scan 4

Dial the 96th Presets

360-degree gap scan

Dial the 97th Presets

scan between two presets

Dial the 98th Presets

presets cruise

Dial the 99th Presets

360 degree continuing scan

3.2 System OSD menu operation


This section will detail the operation of OSD menu. Power is switched on, the dome camera self-test after the monitor screen will display the following information:
Control Protocol: PELCO-P
Serial Information: 2400, N, 8,1
dome camera Address: 1

Since different control keyboard on the dome camera operation method are not identical, specific operations, please contact the keyboard dealer.
1. To enter the main menu: Call 95 preset points, will enter the OSD main menu. IRIS-(aperture opening) is to identify key, IRIS + (aperture closure) is a key to exit the menu.
2. Into the other menu: up / down shake the joystick, so that the cursor is pointing to a menu, press IRIS-key, to enter the menu.
3. Function options: up / down shake the joystick, so that the cursor is pointing to a function key, according to IRIS-key, select the current function.
4.
Parameters: up / down shake the joystick, select parameters, according to IRIS-key, save the current parameters.
5. Save Settings: Press IRIS-key, save the current settings, when there is valid under the appropriate prompt.
6. Exit menu: up / down shake the joystick, so that the cursor point to the menu “EXIT” option, then IRIS + button to exit OSD menu.
7. To return to the previous one menu: up / down shake the joystick, so that the cursor menu, point to “BACK” option, then IRIS-key, to return to the previous menu level.
Notes: 1. Settings for different ball machine, ball machine displays the contents of the different power.
The following describes in detail the use of ball machine OSD menu operation.
3.2.1 Main Menu
Ball machine power and working properly, call the 95 preset points, into the main menu screen display shown in Figure 3-1.

MAINMENU

<SYSTEM INFORMATION>

<ADDR SETTING>

<MOTION>

<PATTERNS>

<CAMERA>

<CRUISE>

DISPLAY SETUP ON

RESTORE FACTORY DEFAULT

REBOOT SYSTEM

EXIT

Image 3-1 MAINMENU

Description of the contents of the main menu

<SYSTEM INFORMATION>Display cameras’ basic informations

<ADDR SETTING>Can setting soft dome’s address.

<MOTION> Parameters setting.

<PATTERNS> patrol scan setting

<CAMERA>lens setting

<CRUISE SETTING> presets cruise setting

DISPLAY SETUP display setting

RESTORE FACTORY DEFAULTRestart lens, recover parameters as default configration, recover factory setting.

REBOOT SYSTEM System restart, To re-power-on reset

EXITexit OSD MENU

  1. Menus for execute functions basic operations

1. In Figure 3-1MAINMENU the main menu, up / down shake the joystick, so that the cursor is pointing to a menu item or feature option;
2. Press IRIS-key, to enter the menu or perform a particular function
3.2.3 <SYSTEM INFORMATION> (System Information menu)
       
In Figure 3-1 MAINMENU the main menu, up / down shake the joystick, so that the cursor point <SYSTEM INFORMATION>, then IRIS-key, enter Figure 3-2 System Information menu.

SYSTEM INFORMATION

COM 9600,N,8,1

ADDRESS 1

PROTOCOL PELCO-D

PRESETS 256

SOFTWARE VERSION V5.2

BACK

EXIT

Image 3-2 SYSTEM INFORMATIO system information menu

SYSTEM INFORMATION use for check camera’s current basic informations. It’s functinon indtroduce as follow:

COMSata informationDisplay cameras current SATA BAUD Rate, Parity bit, data bits,stopbits of information.

ADDRESS Dome camera’s address, displays the current ball machine address coding ,0-255.

PROTOCOLControl protocolDisplays the current ball machine communication protocol

SOFTWARE VERSIONdisplay current software version.

BACKback to main menu.

EXIT exit menu setting.

Note: The System Information menu, the various elements in this menu can not be changed.

3.2.4 <ADDR SETTING> (Address Settings menu)
    
In Figure 3-1 MAINMENU the main menu, up / down shake the joystick, so that the cursor point <ADDR SETTING>, then IRIS-key, enter the Figure 3-3ADDR SETTING address settings menu.

ADDR SETTING

ADDR TYPE HARD

ADDR SOFT 3

BACK

EXIT 

Image 3-3 ADDR SETTING address menu setting

In image 3-3 ADDR SETTING Address Settings menu, up / down shaking rocker, ADDR TYPE (address type) value can select HARD (hard address) and SOFT (soft address) in the system installation is complete, you can direct the remote Set ball machine address.
ADDR SOFT: In the ADDR TYPE selection SOFT, you can directly determine the ball machine address.
Attention; soft address and hard address setting must not be confused, or the ball machine out of control, everything is set to be effective needs to be restarted
3.2.5 <MOTION> (PTZ settings)
      In Figure 3-1MAINMENU the main menu, up / down shake the joystick, so that the cursor point <MOTION>, then IRIS-key, enter Figure 3-4 <MOTION> menu.

MOTION

<SET FRAME SCAN>

POWER UP PATTERN 4

PARK TIME 15S

PARK ACTION PATTERN 4

FRAME SCAN SPEED 16

BACK

EXIT


Image 3-4<MOTION>

Menu clarification:

<MOTION>
Menu is used to set PTZ parameters such as movement and orientation angles.

<SET FRAME SCAN>Is used to set the region to scan the left and right pole

POWER UPOn the power to set the menu, on the power to set the ball machine is used to set the power, no control instructions received prior to the implementation of the action. Parameters as follows:

NONE(no)Does not perform any action.

CRUISE(Preset Point cruise): implementation of the preset points, cruise movements.

AUTO SCAN(Continuous scan): implementation of a continuous scanning motion.

RANDOM SCAN(Intermittent scanning): the implementation of intermittent scanning motion.

FRAME SCAN(Area scan): implementation of the regional scan action (regional scanning range was set after the valid).

PRESET 1(Preset point 1): to reach No. 1 preset points.

PRESET 8(Preset point 8): reach the 8 preset points.

PATTERN 1(Pattern scan 1): implementation of the pattern scanning line 1

PATTERN 2(Pattern scan 2): implementation of the pattern scan line 2.

PATTERN 3 (pattern scan 3): implementation of the pattern scanning line 3.

PATTERN 4(Pattern scan 4): implementation of the pattern scan line 4.

PARK TIMEThe time required for the implementation of free movement settings.

Parameter range of 15s, 1 minute, 2 minutes … 59 minutes, 1 hour … 12 hours.

PARK ACTIONExit ball machine menu, in the idle time, the ball machine does not receive any instruction of the implementation of the action.
Free action parameter description:

NONE(no)Does not perform any action.

REAPEAT LAST(Recovery last action): automatically restore to the most recent action.

CRUISE(Preset Point cruise): implementation of the pre-cruise-point action (preset point is set after the valid).

AUTO SCAN(Continuous scan): implementation of a continuous scanning motion.

RANDOM SCAN(Intermittent scanning): the implementation of intermittent scanning motion.

FRAME SCAN(Area scan): implementation of the regional scan action (regional scanning range was set after the valid).

PRESET 1(Preset point 1): to reach No. 1 preset points.

PRESET 8(Preset point 8): reach the 8 preset points.

PATTERN 1(Pattern scan 1): implementation of the pattern scanning line 1.

PATTERN 2(Pattern scan 2): implementation of the pattern scan line 2.

PATTERN 3(Pattern scan 3): implementation of the pattern scanning line 3.

PATTERN 4(Pattern scan 4): implementation of the pattern scan line 4.

FRAME SCAN SPEED Settings area scanning speed, set the ball machine area scanning speed. Parameter range 1 ~ 32.

BACKReturn to Main Menu

EXIT exit the menu setting

 

Function parameters to set the basic operations:

1Image 3-4<MOTION>(PTZ settings) menu, up / down shake the joystick, so that the cursor is pointing to the menu features an option;

2Press IRIS- key

3up/down
Shaking rocker, select the parameters you need;

4Again press IRIS-key

3.2.6 <SET FRAME SCAN>(setting area scan)


Settings area scanning range, specific operations are as follows

In Figure 3-4 <MOTION> (PTZ settings) menu, up / down shake the joystick, so that the cursor point <SET FRAME SCAN>; by IRIS-key, enter the following diagram:

FRAME SCAN

SET SCAN POSITION

CLEAR FRAME SCAN

BACK

EXIT 

Image 3-4-1FRAME SCAN setting area scan

<SET FRAME SCAN>
Menu is used to set the scope of the regional scan.

<SET SCAN POSITION>Set the scope of the regional area scan

<CLEAR FRAME SCAN>Clear area scan range

BACK:
Back to a Menu

EXIT:exit the menu

3.2.7 SET SCAN POSITION(setting area scan )


In Figure 3-4-1 FRAME SCAN Settings area scan the menu, up / down shake the joystick, so that the cursor point <SET SCAN POSITION>; by IRIS-key, enter the next figure

SET FFRAME SCAN

LEFT LIMIT POSITION

IRIS OPEN TO CONTINUE

Figure 3-4-2 to set the left limit position of regional scanning

Shaking rocker, select the area scan the left limit position; by IRIS-key, to confirm the current position is the left limit position, and enter the following diagram:

SET FFRAME SCAN

RIGHT LIMIT POSITION

IRIS OPEN TO CONTINUE

Figure 3-4-3 to set the right limit positions of regional scanning

Shaking rocker, choose the right limit of area scan position; by IRIS-key, to confirm the current position is the right limit position, save the extreme left position and right limit positions, and return to Figure 3-4-1.

3.2.7 CLEAR FRAME SCAN (Clear area scan location)


In Figure 3-4-1 FRAME SCAN Settings area scan the menu, up / down shake the joystick, so that the cursor point <CLEAR FRAME SCAN>; by IRIS-key, enter the following diagram:

CLEAR FFRAME SCAN

IRIS OPEN TO CONTINUE


3-4-4清除区域扫描位置



By IRIS-key, clear the position of the left and right limits of extreme position and return to Figure 3-4-1.

  1. <PATTERN>(Pattern scan)

In Figure 3-4 MAINMENU the main menu, up / down shake the joystick, so that the cursor point <PATTERN> (pattern scan), then IRIS-key, enter the pattern in Figure 3-5 Scan Menu

PATTERNS

PATTERN NUMBER 4

<PROGRAM PATTERN>

CLEAR CURRENT PATTERN

CLEAR ALL PATTERN

BACK

EXIT

Image 3-5 <PATTERN>(Pattern scan) menu

Scan pattern is used to set and clear the pattern scan lines.
Synchronized Scan ID: Select the pattern scan number.
Number range

1 ~ 4. To do the following:


1. In Figure 3-5 <PATTERN> (pattern scan) menu, up / down shake the joystick, so that the cursor point PATTERN NUMBER (pattern scan) number;
2. Press IRIS-key;

Up / down shake the joystick, select the pattern scan number;
4. Press IRIS-key.

3.2.9 <PROGRAM PATTERN> (pattern scan settings)
  “Synchronized scan settings” is used to set the pattern scan lines.
To do the following:

1. Select pattern scan number;
2. Pattern in Figure 3-5 Scanning the menu, up / down shake the joystick, so that the cursor point <PROGRAM PATTERN>;
3. Press IRIS-key, enter the following diagram:

PROGRAM PATTERN

USE THE JOYSTICK OR

KEYBOARD TO MOVE THE

CAMERA TO THE

STARTING POSITION

IRIS OPEN TO CONTINUE 

3-5-1 PROGRAM PATTERN

4. Shake joystick to determine the starting position of the scan pattern;
5. By IRIS-key, will enter the following diagram:

PATTERN

STORAGE USED 

6. Sway away from pole, edit, scan lines and movement, a movement began to record from up to 100 moves, according to IRIS-key, save the settings, return to Figure 3-5;

3.2.10 CAMERA (Lens)

settings menu
In Figure 3-1 the main menu, up / down shake the joystick, so that the cursor point <CAMERA>, then IRIS-key, enter the camera menu controls, enter the settings menu

 

Figure 3-6 CAMERA

Languages

Chinese/English

Multiples Display

ON/OFF

AGC

180 

Blighlight compensate

ON/OFF

Shutter setting

AUTO

Focus setting

AUTO

Brightness setting

110 

Sharpness Setting

013 

Day& night switch

AUTO

Negative Set

OFF

Lens Set

OFF

缺省设置

OFF

   

Figure 3-6CAMERA settings menu

Function parameters to set the basic operations:

1. The lens in Figure 3-6 to set menu, up / down shake the joystick, so that the cursor is pointing to the menu options for a particular function;

2. Press IRIS-key;

3. Up / down shake the joystick, select the parameters you need;

4. Then IRIS-key.

3.2.11 CRUISE (preset points, cruise settings) menu

    In Figure 3-1MAINMENU the main menu, up / down shake the joystick, so that the cursor point <CRUISE>, then IRIS-key, enter the preset point of Figure 3-7 CRUISE cruise settings menu.

 

CRUISE

DWELL TIME [SECS] 6

PRESET LIST 1

1 ON 0 OFF

1234567890 PRESET

1111111111 [1-10]

BACK

EXIT

Figure 3-7CRUISE preset point setting menu
Preset point cruise is used to automatically set the camera preset point of scan lines. To do the following:
1. In Figure 3-7 <CRUISE> (preset points, cruise settings) menu, up / down shake the joystick, so that the cursor point to DWELL TIME [SECS] (pre-cruise waiting time between points), according to IRIS-key, on the up / down shaking rocker, select the waiting time, according to IRIS-key.
2. Then, up / down shake the joystick, so that the cursor points to PRESET LIST (pre-cruise-point list), according to IRIS-key, up / down shake the joystick, choose to participate in pre-cruise-point page, a total of 30 presets can be point involved in cruise, each page you can select 10 preset points, a total of 33 pages, the corresponding parameters 1.2.3. according to IRIS-button to confirm.
3. Then, up / down shake the joystick, so that the cursor points to PRESET LIST (pre-cruise-point list), according to IRIS-key, up / down shake the joystick, choose to participate in pre-cruise-point page, a total of 30 presets can be point involved in cruise, each page can select 10 preset points, a total of 3. the corresponding parameters for the 1.2.3. according to IRIS-button to confirm.
4. Then, up / down shake the joystick, so that the cursor point to 1234567890
1111111111. left / right shake the joystick, choose to participate in the pre-cruise point, the corresponding parameters for the 0,1 by IRIS-key changes to one of choice, 0 is skipped.
5. Shake up / down joystick, select the BACK / EXIT, to save the settings, return to

Chapter四. simple troubleshooting and maintenance4.1

Simple Troubleshooting Table

 

Failure

Possible Cause

Solutions

Electricity without action, no images, light does not shine.

Connected the wrong power cord

Corrections

Power supply is damaged

replace

Bad fuse

replace

Power cord connection is bad

Exclusion

Power are self-test, there are images, not control

IR uniform ball address code, the baud rate setting does not

To re-set the high-speed dome address code and baud rate

Wrong protocol

corrections

RS485 line reversed or open

Check wiring RS485 control line

Unable to complete self-test, there are images associated with motor tweet sound

Mechanical failure

Maintenance

Camera Tilt

Straightened

Power is not enough

Replacement to meet the requirements of the power supply, it is best to power the ball on the near-infrared uniform

Image instability

Video line connection is bad

Exclusion

Power is not enough

replace

Blur

Manual focus on the state

Operation of any infrared uniform ball or call a preset point

IR control of a uniform-speed ball non-stop or delay

Power is not enough high-speed Dome

Replacement to meet the requirements of the power supply, it is best to power on the high-speed ball in the vicinity

Check control of the most distant high-speed ball match whether to join the resistance

The most far away from the control of the ball-type cameras by adding matching resistor

Far from 485 the signal attenuation

Bold Line of Control

Converter 485 is not enough driving force

Replacement of a source converter

 

 

4.2 After Service


    Dear users, in order to ensure the full enjoyment of your ball machine services, please read the following products and services charter.
(A) I-ball machine company limited warranty and lifetime maintenance services
1. The limited warranty period from the date of sale for 12 months, in the limited warranty period, you will enjoy the products fault free service, delivered or sent by the user’s maintenance (improper use of man-made causes of failure or an irresistible The fault does not belong to the scope of the warranty).
2. In more than 12 months limited warranty from the date of the product life-long failure of the implementation of paid maintenance services.
(B) The ball machine repair response time
1. Users will be sent to the company from the date of product, 24-hour response service.
2. Customers return products to our company, please advance with my company-related contact, and then returned to our company products. Otherwise, the situation appears not timely maintenance by the user themselves.

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s